Linear Gate Installation Nationwide

Linear Gate Installation in Henderson: What to Know First

Linear gate installation in Henderson typically runs between $1,800 and $4,600 for a complete single swing or slide gate with a new operator, depending on gate size, post condition, and the operator series you already own or choose to install. We’re an independent Linear service provider, not a factory shop, and we complete most Linear installations in one to two days once parts and materials are on hand. The written price is in your hands before any work starts, so there’s no guesswork on the invoice.

Call (775) 210-7739

This page is for homeowners in Henderson who already have a Linear operator, are replacing a gate that’s worn past repair, or have a Linear board and arm sitting in the garage waiting for the right crew. If you’re not sure whether your existing Linear gear is worth building a new gate around, call (775) 210-7739 and we’ll talk it through. A live person answers, day or night.

How Linear Products Fail – and How We Fix Them

Linear operators are everywhere in Henderson, especially the older APeX and the newer LS and LRA series. They’re solid machines, but the desert does specific things to them, and a new gate hung on a tired operator is a warranty claim waiting to happen. Here’s what we see on Linear work in this area.

• APeX limit switch drift. The APeX series uses mechanical limit cams that slowly walk out of position as the motor heats and cools through Henderson’s 30-degree overnight-to-noon swings. The gate starts stopping three inches short, then six, then it’s slamming the post. We re-set the limits and inspect the cam set screws during installation rather than just bolting on a new gate and calling it done.
• LRA family gearbox wear from heat cycling. Linear’s LRA residential swing operators run a nylon worm gear that gets brittle after years of 105-degree afternoons. If your LRA sounds like a coffee grinder when the arm moves, the gear train is on its way out. When we install a new gate, we open the gearbox, check the grease and gear faces, and tell you honestly whether the operator has another five years or five months.
• Photo eye and safety edge misalignment after gate hang. Most Linear installs fail final inspection because the safety eyes and edges aren’t reconciled with the new gate’s swing arc. A gate that’s half an inch wider than the last one can shadow the photo beam and leave the operator blinking a fault code. We align every safety device to the new gate travel before we hand it back.
• Older Linear control boards with dead relay outputs. The original APeX and MegaCode boards run their motor relays hard, and we’ve replaced enough of them to recognize the symptom: the operator hums, the capacitor checks out, but the gate never moves. During installation we test the board under load before mounting anything. If the relay is weak, you decide whether to replace it now or nurse it along, and we quote both ways in writing.
• Undersized operators on oversized post-mounted gates. Henderson HOAs near Inspirada and Anthem often permit heavy wrought-iron swing gates that outweigh the operator’s duty rating after a few years of added stucco and decorative steel. We check the actual gate weight against the Linear model’s rated capacity before installation and tell you if the operator is going to be a mismatch. Sometimes the right move is a step up in operator class rather than a new gate at all.

Our Linear Gate Installation Process

Every Linear job follows the same sequence, whether it’s a single pedestrian gate in Green Valley or a double swing driveway gate out near Lake Las Vegas.

1. 1
   Call and conversation. You reach a live person at (775) 210-7739. We ask about the gate, the operator model, and what’s not working right now. We schedule a time that works, including quiet hours if kids or shift workers are sleeping.
2. 2
   On-site inspection and honest diagnosis. We measure the posts, weigh the gate if needed, open the Linear operator, and trace the wiring before we recommend anything. Cody Beckman and our techs would rather spend ten extra minutes finding the real problem than swap a part that didn’t need swapping.
3. 3
   Written price before work starts. You get a line-item quote covering materials, labor, and any operator or board work. The number on that sheet is the number you pay, unless you ask us to add something mid-job, and that gets a new written approval first.
4. 4
   Parts decision: OEM or quality aftermarket. For Linear work, some parts should be OEM: control boards, limit assemblies, safety edges. Others, like arms, brackets, and hinges, can come from quality aftermarket suppliers at a lower price without touching warranty status. We lay out both options and let you choose.
5. 5
   Installation and set-up. We hang the gate, mount the operator, wire the safety eyes and edges, set the limits, and test the full open-close cycle at least ten times under load. We set force and sensitivity so the gate reverses on real resistance but doesn’t false-trip in the wind.
6. 6
   Cleanup, photo, and walk-through. Our crew wears shoe covers when we’re near the house, lays drop cloths where we’re working inside the garage or entry, and sweeps up metal shavings and wire clippings before we leave. We photograph the clean work area, walk you through the operation, and hand you the written record. Every Linear install is covered by our 365-Day Done Right Promise.

What Linear Gate Installation Costs in Henderson

Here are realistic numbers for the Linear jobs we do most in Henderson. These are installed prices including the gate, operator labor, and basic wiring, assuming sound existing posts.

• Pedestrian gate with Linear operator: $1,800 – $3,200
• Single swing driveway gate with LS or LRA operator: $2,400 – $4,200
• Double swing driveway gate with dual operators: $3,800 – $6,500
• Sliding gate with Linear slide operator: $3,200 – $5,800
• Reusing your existing Linear operator, new gate only: $1,200 – $2,800

What moves the price: gate weight and size, post condition (rotted steel posts or cracked concrete need replacing first), distance from the house to the gate for power and safety wiring, and whether your existing Linear board and controls are sound or need attention. Call (775) 210-7739 for a free estimate on your specific gate, and you’ll see the exact number in writing before we start.

Why Henderson Homeowners Call Latch and Post Gate Repair Henderson for Linear Work

We’re a gate-only shop that’s part of the Cedarwell family, and we’ve been at this since 2009. That narrow focus matters when you own a Linear: our techs know how Linear boards behave in Henderson heat, which APeX quirks show up across years of installs, and which parts are worth sourcing OEM versus the aftermarket alternatives. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which means if your Linear operator is beyond saving and you’d rather switch brands entirely, we can give you a straight answer about what that costs and how the wiring changes.

Every visit includes the Cedarwell Care Promise: a written price before work starts, shoe covers and drop cloths where we’re inside, and a photo of the cleanup before we leave. A live person answers the phone 24 hours a day, seven days a week. No voicemail maze, no callback queue. And if something isn’t right on a Linear install, the 365-Day Done Right Promise means we make it right, no fine print.

A gate that works quietly is one you stop thinking about, and that’s exactly the goal.

FAQs