Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Henderson Homeowners
A gate that won’t close is a gate that isn’t doing its job, and in Henderson, where backyard pools, dogs, and curious kids are part of daily life, a working gate matters. For fast, reliable Automatic Gate Repair, homeowners trust our local team. We’re Latch and Post Gate Repair Henderson, part of the Cedarwell family since 2009, and we focus on one thing: getting your gate latching, sliding, and swinging the way it should, without leaving a mess behind. Most repairs in Henderson are completed the same day we arrive, and you’ll always get a written price before any work begins. If your gate is stuck, sagging, or refusing to respond, call (775) 210-7739 and a live person will answer, any hour, any day.
Key Takeaways
- We repair every type of gate common to Henderson homes, including iron, steel, wood, sliding, and driveway gates.
- Every job starts with a written price, and our technicians wear shoe covers and lay drop cloths before stepping inside.
- The 365-Day Done Right Promise covers every repair. If it isn’t right, we make it right.
- Calls are answered by a live person 24/7, not a voicemail system.
Driveway Gate Repair
Driveway Gate Repair means restoring a gate that has stopped opening, closing, or sealing properly, whether it’s a manual swing gate on a side yard or a motorized driveway gate protecting the whole property. In Henderson, driveway gates take a beating from hard water, dust storms, and constant afternoon sun, and the first sign is usually sagging at the hinge side or a motor that hums but won’t move. We work on LiftMaster, FAAC, and BFT operators, and many driveway gate repairs fall between $180 and $340 for common hardware and alignment fixes. You’ll see the exact number in writing before we touch anything.
Sagging Hinge Correction
A driveway gate that drags on the ground is usually a Hinge & Post Repair issue, and the longer it drags, the more damage it does to the post and the concrete below. We inspect the hinge welds, replace worn bushings or bearings, and re-align the gate so it swings freely again. This kind of repair is straightforward when caught early and much cheaper than replacing a bent post.
Operator And Sensor Calibration
When a driveway gate starts reversing on its own or only opens halfway, Gate Realignment and sensor recalibration are usually needed. We set open and close limits precisely, test the obstruction detection, and confirm the gate stops and reverses on contact. Before we leave, we run the gate through a full cycle several times to make sure it’s stable.
Styles & brands we work with
Gate Welding
Gate Welding is the structural repair that fixes what bolts alone cannot, including cracked steel frames, broken hinge points, and torn metal where the gate meets the post. Henderson’s dry heat causes steel to expand and contract, and over time those movements concentrate stress at welds. We weld on-site with equipment suited to the gate’s metal thickness, and the cost for most welding repairs starts around $220 and ranges up to $490 depending on the number and length of welds required. You’ll have the written figure before the first spark.
Cracked Frame And Hinge Welds
A crack near a hinge isn’t cosmetic. It means the gate’s weight is tearing its own frame apart one swing at a time. We grind the area clean, weld the crack fully, and add reinforcement where the design allows it. This repair usually keeps the gate solid for years rather than months.
Broken Or Torn Post Attachments
When the weld between a gate post and the fence panel fails, the entire assembly loses rigidity. We re-weld the attachment points, check the post for plumb, and confirm nothing shifted during the repair. Keeping the post straight is just as important as making the weld strong.
Commercial Gate Repair
Commercial Gate Repair covers the gates that protect parking lots, loading docks, storage facilities, and apartment communities across Henderson. These gates cycle dozens or hundreds of times a day, which means parts wear faster and failures interrupt more than just one household. We service commercial operators from BFT, Linear, and LiftMaster, and pricing depends on the specific failure, with common repairs running from $350 to $1,200. Property managers don’t need a vague guess; they need a written quote and a repair that holds up under constant use.
High-Cycle Operator Repair
Commercial gate motors run until parts inside break, not just until they get tired. We diagnose worn gears, failing capacitors, and burned contactors, then replace the specific component instead of selling an entire operator when it isn’t needed. This keeps the repair cost in line with the actual failure.
Track And Roller Alignment
Sliding commercial gates with rollers out of alignment create uneven wear on the track and strain the motor. We adjust the roller brackets, check the track for warping, and clean the path so the gate slides without fighting itself. Getting this right reduces future breakdowns.
Iron Gate Repair
Iron Gate Repair addresses bent pickets, rust-weakened frames, and damaged latch hardware on solid iron gates throughout Henderson’s older neighborhoods like Green Valley and Whitney. Iron gates are strong but brittle at certain stress points, and children climbing on them or a car tapping them in a driveway can bend sections that then misalign the latch. Most iron gate repairs run between $150 and $350, and the written quote covers the parts, the time, and the cleanup.
Bent Picket Straightening
A bent picket changes the look of the whole gate and can prevent the latch from engaging. We straighten bent sections using controlled pressure, not heat when avoidable, so the metal keeps its strength and original finish. When a picket is too far gone, we replace it and match the surrounding pattern.
Rust Treatment At Latch Points
Henderson’s low humidity doesn’t stop rust from forming where moisture collects after rain or sprinkler overspray. We remove surface corrosion at latch and hinge points, treat the area to slow future rust, and perform Lock Repair so the gate closes securely. Keeping the latch area clean is the cheapest insurance an iron gate has.
Sliding Gate Repair
Sliding Gate Repair focuses on the cantilever and track-style sliding gates that are common in Henderson’s Anthem and Southern Highlands communities. These gates fail when rollers wear flat, tracks collect debris, or the motor’s chain or belt loses tension. We repair sliding gates from brands including LiftMaster and BFT, and the repair typically costs between $250 and $550. Because these gates are heavy and move under power, we take extra care to set the stops and sensors correctly.
Roller And Bearing Replacement
Flat-spotted rollers make a sliding gate shudder and strain the motor on every cycle. We replace worn rollers and bearings, clean the track, and test the gate under load to confirm smooth travel. This is one of the most common repairs we do for sliding gates in Henderson.
Belt And Chain Tension Adjustment
When a sliding gate hesitates or jumps during travel, the drive belt or chain has usually lost proper tension. We set the tension to the manufacturer’s specification, inspect the sprockets and idlers for wear, and confirm the gate moves at the correct speed. Proper tension extends the life of both the drive components and the operator motor.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is the specialty work of restoring decorative iron gates, the ones with scrollwork, finials, and ornamental pickets that make a statement at an entryway. Unlike structural iron gates, wrought iron pieces require gentler techniques because the decorative elements are often thinner and more fragile. In Henderson, these gates appear on custom homes in Anthem and Green Valley, and repairs usually run from $200 to $600 depending on the ornamentation involved. We preserve what’s original and replace only what can’t be saved.
Decorative Element Restoration
Scrollwork and finials get knocked loose by wind, delivery trucks, and years of small impacts. We re-secure loose elements, straighten bent scrolls by hand where possible, and repaint the repaired area to blend with the surrounding iron. The goal is a repair that doesn’t announce itself.
Ornamental Latch Replacement
Many wrought iron gates use specialty latches that big-box stores don’t carry. We match the existing latch style, and when the original is unavailable, we fabricate or source an equivalent that fits the gate without modification. A new latch on an old gate should look like it was always there.
Metal Gate Repair
Metal Gate Repair covers the broader category of steel, aluminum, and tubular metal gates that don’t fit neatly into the iron or wrought iron categories. These are the powder-coated steel gates and aluminum driveway gates found across Paradise, Enterprise, and Winchester. Metal gates suffer from hinge wear, latch misalignment, and post movement, and our repairs usually cost between $150 and $400. We specify the correct replacement hardware for the specific metal so you don’t get a steel hinge on an aluminum gate, which causes corrosion.
Hinge And Bracket Replacement
Metal gates hang their entire weight on two or three hinges, and when those hinges wear, the gate drops. We replace worn hinge pins and brackets with hardware rated for the gate’s weight, then re-align the gate so the latch catches cleanly. The difference is immediate: no more lifting the gate to close it.
Post Shift Correction
A leaning metal gate is usually a post problem, not a gate problem. We check whether the post has shifted in its concrete footing, reset it if needed, and confirm the gate swings true in both directions. Correcting the post now prevents the gate from tearing out the hinges later.
Wood Gate Repair
Wood Gate Repair addresses the gates common to Henderson’s residential backyards: redwood and cedar gates that warp, sag, and split in the desert sun. Wood gates need attention for different reasons than metal, mostly moisture loss and framing joints that loosen as the wood dries. Repair costs for wood gates typically run between $140 and $320. We match the existing wood species and hardware style so the repair blends in, and we treat the frame to keep it stable as the seasons change.
Frame Squaring And Brace Repair
A wood gate that won’t latch is usually out of square because the diagonal brace has failed or the frame joints have loosened. We re-square the frame, reattach or replace the cross brace, and drive the gate through a full swing to confirm the latch engages. This is the most effective repair for a sagging wood gate.
Split And Rot Repair
Even in Henderson’s dry climate, sprinkler overspray and monsoon rains can rot the bottom rail of a wood gate. We remove the damaged section, splice in a matching piece, and seal the end grain to slow future moisture absorption. Caught early, this repair keeps the gate functional without a full rebuild.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We’re factory-trained on the equipment families across Henderson actually own. LiftMaster is the brand we see most often on residential driveway gates, and we stock the common gears, sprockets, and control boards for their operators. We know the difference between a capacitor issue and a logic board failure on LiftMaster units, which means the right fix happens on the first visit instead of the third.
FAAC and BFT operators appear on many gated community entries and commercial properties across the valley. We service their hydraulic and electromechanical models, and we keep their sensor and loop detector settings within manufacturer spec. Whether you have a Linear slide operator on a commercial track or any other make, we can diagnose and repair it properly. A free estimate and a written price apply to every brand.
Signs You Need a Pro Right Now
- The gate drags on the ground when you open or close it. This means the hinges or the post have shifted, and every movement adds more damage to the gate frame and the concrete below. A dragging gate gets harder to fix the longer it scrapes.
- The motor runs but the gate doesn’t move. When you hear the operator working and nothing happens, the chain, belt, or gear has failed. Continuing to press the remote button can burn out the motor entirely.
- The gate reverses for no reason or stops halfway. Safety sensors and limit switches are out of adjustment, and an unpredictable gate can close on a car, a kid, or a pet. This is a repair we treat as urgent because the safety system is compromised.
- The latch won’t catch, even when you lift the gate into place. A latch that won’t engage means the gate can blow open in the next windstorm. For families with dogs or a pool, an unlatched gate is a daily risk until it’s fixed.
- You see a crack at a weld or hinge point. Cracks in metal gates grow quickly because the gate’s weight works against the metal with every cycle. Welding a small crack now costs a fraction of replacing a torn-out frame later.
Our Process, Step by Step
- 1
You call and a live person answers. Every call to (775) 210-7739 is picked up by a real person, not a recording. We ask what the gate is doing, what brand it is, and when you need it fixed. Most Henderson calls get same-day or next-day service.
- 2
The technician arrives and inspects. We check the hardware, the operator, the sensors, and the posts before recommending anything. You’ll get a written price that covers the parts, the labor, and the cleanup. There’s no pressure to accept, and the inspection itself is free.
- 3
We protect your property before any work starts. Shoe covers go on before we walk inside your home or through your entryway. Drop cloths go down anywhere we’re working. If you have dogs, we ask before entering the yard, and if kids are sleeping, we use quiet tools. Our C.A.R.E. values are simple: ask before we move or touch anything, respect your time and quiet hours, and explain the price before the work.
- 4
The repair or replacement is completed. We work methodically, test each component we touch, and don’t call a job done until the gate cycles correctly multiple times. If we find a second issue during the repair, we show you what we found and quote the additional work before doing it. You’ll never get a surprise on the final total.
- 5
We clean up and show you the proof. We sweep the work area, remove any packaging, and take a photograph of the clean site before we leave. The 365-Day Done Right Promise means if anything about the repair isn’t right within a year, we come back and make it right. No argument, no fine print.
How Much Does Gate Repair Cost in Henderson?
Gate repair in Henderson typically costs between $140 and $600 for most residential work, with simple latch and hardware replacements at the low end and structural welding or motor component replacement at the higher end. A wood gate latch replacement often lands around $140 to $180, while a welded steel frame repair usually runs $220 to $490. Commercial repairs can reach $1,200 or more depending on the operator and the parts involved.
What affects the price is straightforward: the type of gate, the extent of the damage, whether the operator’s control board or motor is involved, and whether parts need to be sourced from a specific manufacturer. We avoid unnecessary markups by stocking common LiftMaster, FAAC, and Linear components on our trucks. The best way to avoid overpaying is to get the repair done before a small problem, like a worn hinge, turns into a large one, like a torn-out post. A free, written estimate from Latch and Post Gate Repair Henderson includes the diagnosis, the pricing breakdown, and the cleanup. You’ll see the exact number before we start, and that number won’t change unless we find something new and get your approval first.
Our Service Area Near Henderson
We serve the entire Henderson valley, including Green Valley, Anthem, Whitney, and the newer communities along the southern edge of the city. We also take calls for Gate Repair in North Las Vegas, Gate Repair in Boulder City, and nearby areas like Paradise, Enterprise, and Sunrise Manor. If you’re in Southern Highlands or near Nellis AFB, you’re in range too. A live person answers every call, 24 hours a day, seven days a week, so call (775) 210-7739 and tell us what’s going on with your gate. We’ll let you know when we can be there.
Serving Henderson, NV - Our Local Coverage Area
We’re based in the Henderson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Henderson
Gate repair is the work of restoring a gate that has stopped functioning properly, whether it’s a sagging hinge, a failed latch, a bent frame, or an operator that won’t respond. In Henderson, it covers everything from wood backyard gates to commercial sliding gates. The goal is to make the gate open, close, and seal the way it did when it was new.
Most residential gate repairs in Henderson are finished in one to three hours. Simple latch and hinge work is often under an hour, while welding and motor component replacement can take longer. We’ll give you a time estimate with your written quote before any work begins.
Residential gate repair in Henderson usually falls between $140 and $600. The exact price depends on the gate type, the failed component, and whether welding or operator repair is required. Every job gets a written quote first, so you’ll never wonder what the final number is. Call (775) 210-7739 for an exact quote.
Yes. We repair LiftMaster residential and commercial operators, including gear replacement, limit switch calibration, and control board diagnosis. We stock common LiftMaster parts on our trucks so many repairs happen in a single visit.
In most cases, yes. We keep same-day and next-day availability for Henderson homeowners, and our live operators can tell you the earliest window when you call. For commercial properties, we prioritize urgent failures that affect access or security.
Every repair and installation is covered by the 365-Day Done Right Promise. If the work isn’t right within a year, Latch and Post makes it right, no argument and no fine print. That promise applies to the parts we install and the labor we perform.
Clear a path to the gate so our technician can bring tools and parts through without navigating clutter. If you have dogs, secure them before we arrive, and let us know about any gate quirks, like a remote that works intermittently. You don’t need to move anything inside the house; we handle the floor protection and cleanup ourselves.
Schedule Your Gate Repair Service in Henderson Today
A gate that works is a gate that keeps your kids in the yard, your dog off the street, and your home feeling secure. Call (775) 210-7739 today for a free, no-obligation estimate from Latch and Post Gate Repair Henderson. A live person will answer, listen to what your gate is doing, and schedule a time that works for your family. You’ll get a written price before we start, and the 365-Day Done Right Promise after we finish.
Written by Cody Beckman, Owner at Latch and Post Gate Repair Henderson, serving Henderson since 2009.