Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Henderson Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller replacement parts throughout Henderson, with most hinge swaps running $140 to $260 installed and roller replacements typically landing between $95 and $180. We carry common Ghost Controls hinge and roller hardware on the truck, so most Henderson homes are back to a smoothly swinging gate the same day we arrive. The way owners usually discover the part has failed is simple: the gate starts dragging on the ground, or it groans every time it opens, or it won’t close flush against the post anymore.

Call (775) 210-7739

In Henderson’s dry heat and alkaline dust, the factory rollers on Ghost Controls gates take a beating. We see it constantly out in Anthem, Green Valley, and over near Inspirada where HOA-managed iron swing gates sit in full sun for years. The roller bearings dry out, the nylon wheels flatten on one side, and the steel hinge pins slowly wear into an oval. By the time the gate is scraping the driveway or the opener is cycling short, that hinge or roller has typically been telling you for months.

We’re an independent service provider, not affiliated with Ghost Controls, which means we match the part honestly rather than upselling a factory-branded box when a quality equivalent does the same job for less.

Which Ghost Controls Models This Applies To

Ghost Controls produces two primary swing-gate hardware lines: the standard residential kits (the AXDP, R3, and TSS1 series) and the heavier-duty dual-gate packages built for wider or solid-wood gates. The hinge and roller design differs between them, and matching the replacement to the right series is where we see the most ordering mistakes from homeowners who guess.

Here’s the compatibility reality we work with every week in Henderson:

• R3 and AXDP series gates use a top hinge with a formed steel leaf and a captured roller that rides inside the top track. These rollers are open-bearing and fail faster in dusty environments like ours.
• TSS1 and heavier tubular-steel gates use a taller hinge assembly with grease fittings and larger-diameter roller wheels, usually 2.5 to 3 inches, and those do better here but still wear the pins over time.
• OEM Ghost Controls hinges are stamped from 11-gauge steel on most current models, with powder-coat black finish. Quality aftermarket equivalents from brands we routinely fit are full-weld fabricated and use the same bolt pattern and center height, and they often outlast the original coating in Henderson’s UV load.
• The measurement that matters when matching a hinge is the center-to-center distance between the two mounting bolts on the post leaf. On most Ghost Controls residential gates that’s 4 inches, but some early TSS1 gates used 4.5 inches. We always measure before quoting, because a 4-inch hinge that’s driven onto a 4.5-inch pattern either binds the gate or cracks the post over time.

If you can find the model sticker on the opener arm or the gate’s inside frame rail, that gets us most of the way there. If the sticker’s sun-faded or gone, which is common after a few Henderson summers, we’ll match by measuring the hinge leaf, the roller diameter, and the track width. Ten minutes on site beats three wrong online orders.

Signs Your Ghost Controls Hinge or Roller Is Failing

• The gate drags or scrapes at the latch-end of its travel. This almost always means the top roller has worn flat and the gate is riding lower than designed. Homeowners in Henderson often first notice this as a fresh scuff line in the driveway near the closed position.
• The opener motor works hard and then shuts down mid-cycle. Ghost Controls boards run an obstruction-sensing routine, so when a worn hinge makes the gate heavier to move, the opener trips early and backs up. You’ll think it’s the motor; it’s usually the mechanicals underneath.
• The gate leans toward the post or sags visibly when open. That’s the hinge pin ovaling out inside the leaf. Once a steel hinge pin has wallowed, tightening the bolts won’t fix it, and it gets worse every month it’s ignored.
• You hear a metal-on-metal squeal only when the gate starts moving. That’s the roller bearing running dry, and by the time it’s squealing, the bearing race is often scored. Lubricating a failed bearing buys a few weeks, not a repair.
• The gate has to be lifted slightly to close completely. Owners sometimes prop it with a block or kick it into place. That’s a hinge geometry problem, and it means one of the two hinges has dropped enough that the gate’s latch bar no longer lines up with the post catch.

Replacement Cost & What’s Included

In Henderson, a single Ghost Controls hinge replacement with parts and labor typically runs between $140 and $260, depending on whether we’re swapping one hinge or both and whether the gate is a light residential panel or a heavier tubular-steel model. Roller replacement alone usually lands between $95 and $180, including the new wheel, bearing, and track adjustment. If both hinges and the roller set need replacing on a heavier dual gate, the job typically comes in between $320 and $580.

Here’s what that price includes, every time:

The exact price is written out and agreed before any work starts. We don’t open a gate, find a second issue, and surprise you with a larger invoice at the end. The written price covers the hinge or roller, the hardware, track alignment, and cleanup. Parts carry a one-year warranty from us, and the whole job is covered by our 365-Day Done Right Promise: if it isn’t right, we make it right, no argument and no fine print.

DIY or Call Us?

There are a few things an owner can safely check before calling: whether the mounting bolts are loose at the post, whether the roller wheel is visibly flattened or cracked, and whether the track has pulled away from its welded bracket. Loose bolts are a ten-minute fix with a socket wrench, and no special equipment is needed to look at a roller. But actually replacing a Ghost Controls hinge or roller is different from checking it.

These gates are heavy, even the light ones. If you unbolt the bottom hinge without proper support, the gate drops onto you or twists the top hinge, and that becomes a much bigger repair. The springs and counterbalance on Ghost Controls units are under tension, and a gate that springs back mid-repair can break fingers or knock a helper off balance. We do this work with the gate braced, the tension released safely, and the new hinge set to the same center height and swing arc as the original.

If you’ve checked the bolts and the roller looks damaged, that’s the moment to call us at (775) 210-7739. We’ll quote the replacement honestly, and if it turns out we can true up the hinge instead of replacing it, we’ll tell you that too.

FAQs