Linear Access Control Installation Nationwide

Linear Access Control Installation: The Henderson Owner’s Guide

Linear access control installation in Henderson typically runs between $450 and $1,400 installed, depending on whether you’re replacing a failed keypad or adding full telephone entry at the gate. We stock Linear-compatible keypads, receivers, and controllers on our trucks, and most single-part swaps are completed the same visit. The way Henderson owners usually discover a failure: the keypad stops accepting the code after a monsoon rain, or the remote works only from six feet away when it used to reach from the driveway apron.

Call (775) 210-7739

Linear built its reputation on simple, weather-tough access hardware that doesn’t need a degree to operate. The parts we see fail in Henderson are almost always the outdoor-facing components: keypad membranes that crack under ultraviolet exposure, card readers that corrode from irrigation overspray, and antenna wires that work loose when the wind rattles an iron gate against its post. The good news is that Linear designed most of this equipment to be serviced rather than scrapped, which means a failed keypad rarely requires replacing the whole controller. We’ll walk through exactly what breaks, what it costs, and what’s worth fixing.

Which Linear Models This Applies To

We install and service the Linear access control hardware most common on Henderson residential and small-HOA gates: the AE-1000 and AE-2000 telephone entry systems, the AK-11 and AK-21 keypads, the AM-KP keypad, and the older RE-1 and RE-2 receivers that many homes still have wired to Mighty Mule or LiftMaster operators. If you’re holding a part that says “Linear” and “MegaCode,” we carry compatible replacements for it.

Here’s the compatibility gotcha that catches Henderson owners: Linear changed its keypad wiring pinouts between the older RE series and the newer AE and AK lines. A keypad that plugs straight into an AE-1000 board will not wire directly into an RE-1 receiver without a change in the four-wire harness order. We verify the wiring before anything gets mounted, because a quick miswire can smoke a $90 receiver board. The fastest way to identify your system is to open the keypad or controller lid and look for the model sticker on the board itself, not the housing. Linear has been known to change internal boards while keeping the same plastic case.

On the OEM-versus-aftermarket question: we recommend Linear OEM keypads and receivers for anything tied to the primary driveway gate. We’ve installed aftermarket MegaCode-compatible keypads, and they work, but the UV-stabilized plastic on the genuine Linear faces holds up longer in Henderson’s sun. For interior controller components, a quality aftermarket equivalent is usually fine and saves real money.

Signs Your Linear Access Control Installation Is Failing

• Keypad accepts the code intermittently, or only after multiple presses. This is the classic early sign of a keypad membrane breaking down. The rubber buttons lose their dome shape after a few Henderson summers, and the contacts underneath stop closing reliably. If two presses usually works, the membrane is on its way out.
• The remote range has dropped from a hundred feet to about ten. This usually isn’t the remote itself. It’s the receiver’s antenna wire, which gets pulled, pinched, or corroded where it exits the control box. Re-siting or replacing that wire fixes most short-range complaints on Linear MegaCode systems.
• The gate opens on its own or won’t close, but only at certain times of day. Sun angle and temperature affect the photocell and loop detector circuits. In Henderson, we see this on west-facing gates in the afternoon when the box sits in direct sun and the internal relay warms past its tolerance.
• The keypad works, but the wired intercom or phone feature doesn’t ring through. On the AE-1000 and AE-2000 telephone entry models, the phone wire landline or cellular unit often dies before the door control side. We can replace just the communication module without scrapping the entire entry panel.
• You hear a click at the controller, but the gate motor doesn’t start. This points to the relay output failing internally or the low-voltage trigger wire to the operator being severed. We test the relay first with a meter, because replacing a $12 relay beats replacing a $300 controller board.

Replacement Cost & What’s Included

A Linear access control installation in Henderson breaks down like this: a standalone Linear keypad (AK-11 or equivalent) runs $450 to $650 installed. Adding or replacing a MegaCode receiver runs $525 to $750. A full AE-1000 telephone entry system, including the keypad, controller, and phone-call integration, runs $950 to $1,400 installed. Here’s what moves the number: whether we’re swapping a part on an existing working enclosure versus pulling new low-voltage wire through existing conduit, whether the operator needs a new plug-in harness or hard wiring, and whether drywall or masonry anchors are required at the mount point.

Every quote is written before we touch the gate, and that number is the number you pay. Parts and labor are listed separately so you see exactly what you’re buying. Every Linear installation we perform is covered by the 365-Day Done Right Promise: if it isn’t right, we make it right, no argument and no fine print.

DIY or Call Us?

Here’s the honest split. You can safely troubleshoot a few Linear issues yourself: check that the keypad’s mounting screws are snug, look for a loose antenna wire inside the control box, and verify that nothing is obstructing the gate’s path. Those checks take five minutes and cost nothing.

What we’d caution against: opening the controller to rewire anything while the system is powered. Linear control boards run on low voltage, but the operator they trigger can carry line voltage, and an incorrect wire landed on the wrong terminal can damage the board or the motor. If the problem is inside the box, call us at (775) 210-7739. Cody Beckman and the crew carry spare Linear relays, keypads, and receivers, so we can usually diagnose and swap a failed part in one visit without you ever touching a wire.

FAQs