Linear Hinge & Roller Replacement Nationwide

Linear Hinge & Roller Replacement: The Henderson Owner’s Guide

We stock and install Linear-compatible hinge and roller replacements across Henderson, and most swaps run between $140 and $320 installed, depending on your gate’s weight and the condition of the hinge plate. You’ll usually know something’s wrong because the gate starts dragging on the ground, squealing like a stuck pig in the morning cool-down, or hanging crooked at the latch post. Here’s the honest picture: in Henderson’s dry heat and blowing grit, Linear hinges and rollers tend to fail at the bearing, not the steel. The metal lasts. The smooth motion doesn’t.

Call (775) 210-7739

If your gate still opens and closes but sounds and looks tired, that’s the sweet spot for this repair: the rails and posts are usually fine, and we can get the gate back to quiet, square, and gliding in one afternoon. Most Henderson jobs we do are finished in under two hours.

Key Takeaways

• Installed Linear hinge and roller replacement in Henderson typically runs $140 – $320, written up front and agreed before any work starts.
• We carry Linear-compatible parts on the truck for the most common residential swing gate series, so most jobs are done in one visit.
• Symptoms are easy to spot: sagging, scraping, squealing, or a gate that catches and jerks as it swings.
• This is a bearing-and-bushing job more than a welding job, and doing it wrong can distort the gate frame.
• Every repair is covered by the 365-Day Done Right Promise. Every visit includes written pricing, shoe covers, and drop cloths.

Which Linear Models This Applies To

Linear is unusual among residential gate brands because the same core hinge geometry shows up across several of their swing gate series: the Linear SL and SLD slide gate lines and the APeX and classic Linear swing gate operators paired with steel or ornamental iron gates. If your operator is a Linear but the gate itself was fabricated by a local Henderson welder, the hinge and roller almost always follow that same Linear pattern: a 3/4-inch or 1-inch hardened pin running through a greasable steel sleeve or a nylon bushing, mounted to a welded plate.

Here’s the compatibility gotcha we see in Henderson again and again: the hinge pin diameter and the bolt-hole spacing are what matter, not the operator model. A Linear hinge spec’d at 3/4-inch pin with a 2-inch bolt pattern will fit a huge range of gates; waltz in assuming all Linear parts interchange, and you’ll be welding a new plate by sunset. We carry both 3/4-inch and 1-inch pin kits and a selection of roller styles (greasable steel, sealed nylon, and flanged rollers for track guides) so we can match what’s actually on your gate, not what the catalog guesses.

When it comes to OEM versus aftermarket for Linear, our rule of thumb is: OEM or OEM-equivalent for the hinge pin and sleeve, where tolerance matters; either is fine for rollers, where weight rating matters more than the casting logo. We’ll show you both options and the price difference in writing before anything gets touched.

Signs Your Linear Hinge & Roller Replacement Is Failing

• Gate scrapes the ground near the latch side. The top hinge pin or bushing has worn enough that the gate has dropped a quarter inch or more. You’ll see fresh concrete dust or a rubbed-bare arc on the driveway.
• Loud metallic squeal or “groan” when opening. That’s the hardened pin grinding against a worn bushing. Greasing it buys a week, not a season.
• Gate jerks or catches partway through the swing. The roller has flat-spotted or the hinge is binding against the post plate. That catch-and-release motion is the gate losing its arc.
• Visible side-to-side wobble when the gate is half open. Hinge play has exceeded what the operator can control. Every cycle wears the operator’s arm and gear faster.
• Latch no longer lines up with the strike plate. The whole gate has shifted on its hinges. In Henderson’s dry air, the gate frame rarely moves; the hinge pins do.

If two or three of these are present, the hinge and roller set is overdue. Catching it now means a $200 fix instead of a warped gate frame or burned operator motor later.

Replacement Cost & What’s Included

Across Henderson, an installed Linear-compatible hinge and roller replacement typically runs between $140 and $320 for a standard single swing gate. That’s parts and labor together: the hinge pin kits or replacement hinges, the rollers, the greasable hardware, and the time to remove, align, mount, and test. Where you fall in that range depends mostly on gate weight and reach: a lightweight 6-foot ornamental gate with easy access lands at the bottom; a heavy 14-foot solid steel gate with a warped hinge plate lands at the top.

You’ll see the exact number in writing before we touch a single bolt. No percentage added at the end. No “discovered an extra problem” phone call. If we find something else while the gate is off, we stop and explain it with a new written number, and you decide. Every replacement is backed by the 365-Day Done Right Promise: if it’s not right, Latch & Post makes it right. Latch and Post Gate Repair Henderson is an independent service provider and is not affiliated with Linear.

DIY or Call Us?

With the gate open and locked, you can safely check the obvious things: grab the gate at the latch end and lift. If it moves up more than a quarter inch, the hinge pins or bushings are shot. Look for metal shavings around the hinge, and listen to the gate as it swings. Those are all safe diagnostics. What’s not safe or smart to do yourself is holding a 300-pound gate on a floor jack while you drive out a seized hinge pin and hope the plate doesn’t shift. That’s how we see fingers pinched, gates dropped on toes, and post plates welded three degrees off square.

This is also the part of the job where doing it wrong is expensive to reverse. A hinge installed slightly misaligned will egg-out the new bushing in six months and put your operator’s arm under strain every cycle. If you’d rather it be done once, quietly, and by someone who’ll show you the old parts when it’s finished, call us at (775) 210-7739.

FAQs

Get a Free Estimate from Latch & Post Gate Repair Henderson

If your Linear-equipped gate is sagging, scraping, or screaming, let’s get it fixed before it takes the post or the operator with it. We serve Henderson and nearby communities with written pricing before any work begins, shoe covers and drop cloths inside the house, and a cleanup photo before we leave. A live person answers the phone 24/7. Call (775) 210-7739 now and we’ll get a fair number in front of you.

Written by Cody Beckman, Owner, Latch and Post Gate Repair Henderson at Latch and Post Gate Repair Henderson, serving Henderson and nearby areas.