Gate Parts & Welding Cost - Honest Price Ranges, Free Written Quote

How Much Does Gate Parts & Welding Cost in Henderson, NV?

Most gate parts and welding repairs in Henderson run between $150 and $900, with the average job landing around $325. A simple latch replacement or hinge weld sits at the low end, while a full gate frame fabrication or post re-welding job pushes toward $1,200 or more. The exact number depends on the metal, the damage, and whether the gate is manual or electric (electric gate motors and sensors add cost), but you’ll see your written price before any work begins.

This guide breaks down what Henderson homeowners actually pay in 2026, what drives the price up or down, and where welding and parts replacement overlap. If you’re dealing with a sagging gate, a broken hinge, or a latch that won’t catch, call (775) 210-7739 for a free estimate.

Key Takeaways:

• Typical gate parts and welding work in Henderson costs $150 to $900, with most jobs around $325.
• Welding a broken hinge or gate frame section runs $100 to $400 per weld point.
• Full gate post replacement with welding and concrete work runs $500 to $1,500.
• Electric gate component repairs (motor, sensor, keypad) add $150 to $800 to parts-only jobs.
• You get a written price before any work starts, with no hidden fees.

Gate Parts & Welding Cost Breakdown (2026)

Here’s what Henderson homeowners are paying for common gate parts and welding services in 2026. These are real market ranges based on local material costs, labor demand, and the specific hardware brands we see across Anthem, Green Valley, MacDonald Ranch, and Inspirada.

Service	Typical Price Range (Henderson, NV)	What’s Included
Hinge weld repair (single hinge)	$100 – $250	On-site weld, grinding, alignment check
Gate frame crack weld	$150 – $350	Crack prep, weld, reinforcement plate if needed
Latch replacement (standard)	$120 – $280	New latch hardware, alignment, strike plate adjustment
Latch replacement (heavy duty or locking)	$200 – $450	Upgraded latch, lockbox, keyed entry if applicable
Post re-welding (existing post, no replacement)	$200 – $500	Weld repair at base, grinding, alignment
Post replacement with concrete	$500 – $1,200	Old post removal, new post set in concrete, gate re-hang
Full gate frame fabrication	$600 – $1,800	Custom metal frame welded to size, hardware mounting
Electric gate sensor or limit switch replacement	$150 – $400	New sensor, wiring check, travel re-calibration
Gate motor replacement (LiftMaster, FAAC, Mighty Mule)	$400 – $900	New motor, mounting, programming
Welding on wrought iron decorative elements	$100 – $300 per section	Re-welding separated iron scrolls, pickets, or finials

What moves the price up or down? Gate material matters first. Wrought iron and steel weld cleanly and usually cost less to repair. Aluminum gates require a welder with aluminum-specific equipment, which adds $50 to $150 per job. Tubular steel gates with rust damage often need section replacement before welding, and that pushes the number toward the higher end of each range.

Location inside Henderson also plays a role. Homes in older parts of town, like Pittman or the neighborhoods near Basic Road, tend to have heavier steel gates that have been through twenty or more summers of desert heat. Those often need more prep work before a clean weld is possible. Newer homes in Cadence or West Henderson typically have lighter aluminum or tubular gates that weld faster, but the post concrete may be thinner and need reinforcement.

What Affects Gate Parts & Welding Pricing in Henderson

Henderson’s specific conditions shape pricing in ways you won’t see in other markets. Here’s what actually changes the number on your quote:

• Desert heat and UV exposure on welds. Henderson summers push 110°F, and gates sit in that heat for 12-plus hours a day. Weld points on older gates frequently crack because the metal expands and contracts hundreds of times per year. If the weld failure is from heat fatigue, the surrounding metal may need reinforcement, which adds $50 to $200 compared to a simple re-weld.
• Caliche soil and post stability. Much of Henderson sits on caliche, a rock-hard calcium carbonate layer under the topsoil. Replacing a gate post in caliche often requires longer digging time and sometimes different concrete anchoring, which adds $100 to $300 compared to the same job in softer soil. We see this constantly in Green Valley Ranch and parts of Anthem.
• Wind load on wide gates. Henderson gets sustained spring winds that push on wide double gates. Hinges and welds on a 12-foot or wider gate fail faster than on a standard 4-foot pedestrian gate. If your gate is over 8 feet wide, expect hinge and weld repairs to run on the higher end of the ranges above.
• Electric gate integration. If your gate has no motor, parts and welding are straightforward. If you have a LiftMaster, FAAC, BFT, or Mighty Mule opener, the technician has to disconnect the motor, remove the arm, and re-sync everything after welding. That’s an extra 30 to 60 minutes of labor, which shows up as $75 to $180 added to the bill.
• Rust and age of the existing metal. Henderson’s low humidity slows rust compared to coastal climates, but irrigation overspray hitting a gate post every morning creates localized corrosion. Welding onto rust-weakened steel requires grinding back to clean metal and often adding a gusset plate, which runs $60 to $150 extra per weld point.
• Access and gate weight. A cantilever sliding gate or a heavy steel driveway gate takes two technicians and a lift assist to re-hang after welding. That adds labor time. A typical pedestrian gate is a one-person job.

Every one of these factors is visible on the written quote we give before any work begins, so you can see exactly where the money goes.

How to Save on Gate Parts & Welding in Henderson

You don’t have to accept the first quote blindly, and knowing a few specifics helps you keep costs down without cutting corners.

First, catch hinge and weld cracks early. A hairline crack at a hinge weld point is a $100 to $200 fix. Wait six months until the hinge tears fully off the post, and it becomes a $400 to $800 job with potential post damage. Henderson’s heat cycles turn small cracks into big breaks quickly.

Second, know what brand your electric gate system uses before you call. LiftMaster, Ghost Controls, and Mighty Mule parts are widely available and priced consistently. Viking and DoorKing components cost more and may need ordering. If you can tell us the brand on the phone, we can give a tighter estimate range on the first call.

Third, bundle the work. If one hinge is cracked, the other hinge is often close behind. Replacing both hinges in one visit costs less than two separate trips, because the diagnostic time and travel are already covered. Same logic applies to latches plus a hinge weld: you’re already paying for the service call, so adding a second repair on the same visit typically runs 30% to 40% less than a standalone visit.

Fourth, ask about the weld guarantee. Any reputable gate company should back their welds. At Latch and Post Gate Repair, every weld, hinge replacement, and parts repair falls under our 365-Day Done Right Promise. If the weld doesn’t hold or the latch fails in the first year, we make it right, no argument and no fine print.

Finally, get the free estimate. We provide a written price before any work starts, every single visit. Call (775) 210-7739 and we’ll walk through what your specific gate needs.

Common Gate Parts We Replace and Weld in Henderson

Specific parts fail in specific ways, especially in this climate. Here’s what we see most often across Henderson, from the newer builds in Inspirada to the established neighborhoods near Lake Las Vegas:

Gate Hinges

Hinges carry the full weight of the gate every time it opens. In Henderson, the combination of heat, wind, and constant use works hinge welds loose. Typical hinge replacement or re-welding runs $100 to $250 per hinge. Wrought iron gates from the early 2000s, common in Green Valley and older Anthem sections, often use barrel hinges that weld directly to the post. When those fail, the correct fix is grinding the old weld, aligning the gate, and laying a fresh weld. Skip the alignment step and the gate sags again in months, which is exactly why we check alignment on every hinge job.

Gate Latches

A latch that won’t catch is the most common call we get in Henderson, and it’s usually a $120 to $280 fix for a standard replacement. The heat loosens the internal spring, or the strike plate shifts as the post moves in the caliche soil. For self-closing gates, which many Henderson HOAs require, the latch also works with a spring. That spring wears out, and the gate stops closing fully, which is both a latch issue and a safety issue for pools and pets. Standard spring-loaded latch replacement is on the lower end; a locking latch with keypad or deadbolt runs toward $450.

Gate Wheels and Rollers

Cantilever sliding gates and heavy driveway gates sit on wheels or rollers. Henderson’s fine dust and sand work their way into the wheel bearings and wear them out. Replacement wheels run $80 to $200 each, and if the wheel bracket needs re-welding, add $100 to $200. We recommend checking all wheels on a sliding gate when one fails, because a single new wheel carries uneven load and wears faster than it should.

Gate Posts

The post is the anchor. When a post leans or breaks at the base, the gate will never hang right until the post is fixed. Re-welding a post that’s still structurally sound runs $200 to $500. Full post replacement with concrete removal and new concrete runs $500 to $1,200. In Henderson, we regularly see posts that have been set too shallow in new construction, and the first strong wind season finds them leaning. That’s a warranty issue on the original builder’s work, but it lands on the homeowner to fix, and we address it by setting the new post deeper with proper drainage so water doesn’t pool at the base.

Electric Gate Components

For motorized gates, parts replacement usually means sensors, limit switches, control boards, or the motor itself. A photo eye sensor replacement runs $150 to $400. A control board for a LiftMaster or FAAC gate can run $250 to $600. Full motor replacement runs $400 to $900 depending on the brand and horsepower. We’re factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the right part goes in the first time.

The Welding Process, Step by Step

If you’ve never had welding done on your property, here’s what to expect when we come out. This is the same sequence every time, whether it’s a hinge re-weld in Anthem or a post replacement in Cadence.

1. Inspection and written quote. The technician looks at the weld point, the gate alignment, the post condition, and the surrounding hardware. You get a written price before anything is cut, ground, or welded. No pressure, no surprises.
2. Surface preparation. The technician grinds away rust, old weld material, and paint around the repair area. Clean metal makes a strong weld. This step matters more in Henderson because painted surfaces bake in the sun and develop micro-cracks that weaken a fresh weld if left in place.
3. Alignment and clamping. The gate gets positioned and clamped so the weld sets correctly. For a hinge weld, this means leveling the gate and setting the gap between the gate and post. For a post weld, the post gets braced plumb and square.
4. Welding. The actual weld pass happens with the appropriate rod or wire for the metal. Steel and wrought iron weld with standard equipment. Aluminum requires different wire and shielding gas, which is why we carry both setups on the truck.
5. Cooling and cleaning. The weld cools naturally, then the technician grinds any rough edges and cleans the area. You won’t be left with sharp spatter or jagged edges on a gate your kids touch daily.
6. Re-hang and testing. The gate goes back on, the hinges get lubricated if needed, and the gate swings full travel. For electric gates, the motor gets re-connected and the open and close limits get re-checked.
7. Cleanup verification. We put down drop cloths before we work and wear shoe covers if we step inside. Before we leave, we take a photo of the cleaned-up worksite. That’s part of the Cedarwell C.A.R.E. routine on every job, not an upsell.

Henderson-Specific Pricing Notes

Henderson is not Las Vegas, and the pricing landscape is different enough that it’s worth calling out. Here’s what we see specifically in the Henderson market:

HOA communities require self-closing gates. Large sections of Henderson fall under HOA rules that mandate self-closing, self-latching gates for pools and side yards. That means more spring-loaded hardware, more latch and hinge wear, and more frequent replacement cycles than homes without those rules. If your HOA sends a notice about a gate that won’t latch, the fix is usually a $120 to $280 latch replacement plus possible spring replacement. Call us before the HOA deadline, not after the fine.

Block wall construction changes post anchoring. Many Henderson homes have cinder block perimeter walls, not wood fences. Gate posts that anchor into block walls need different hardware, and welding onto a post set in a block wall requires different preparation than a post set in the ground. Expect block wall post work to run $50 to $150 more than ground-set post work.

Dust and sand require more maintenance. The desert dust that blows through Henderson isn’t just cosmetic. It gets into hinge pins, latch mechanisms, and wheel bearings. We recommend a quick hinge and latch check every spring. Catching wear before failure is cheaper than reacting to it, and Henderson’s climate makes that check worth doing.

Pool gates need self-closing compliance. Henderson city code and Nevada state law require pool gates to self-close and self-latch. That’s a safety regulation, not a suggestion, and it affects what parts we can use. A pool gate latch replacement typically runs $180 to $350 because the hardware has to meet code with proper spring tension and placement height.

For more on the range of parts and welding work we handle, see our Gate Parts & Welding in Henderson service page. And if you’re still deciding whether your gate needs repair or replacement, the question many homeowners ask is answered below.

Is It Cheaper to Repair or Replace a Gate?

For most Henderson gates, repair is dramatically cheaper than replacement. A hinge weld, latch replacement, and post touch-up on a standard steel gate runs $300 to $700 total. Replacing that same gate with a new steel gate installed runs $1,200 to $3,500, depending on size, material, and whether it has a motor. Replacement only makes sense when the gate frame itself is rusted through in multiple places, or when the post has failed and the gate design can’t be saved. If you’re unsure, call (775) 210-7739, and we’ll tell you straight whether your gate is worth saving.

Can You Fix My Gate the Same Day?

Most hinge welds, latch replacements, and single-post repairs are done same day. The service truck carries welding equipment, common latch hardware, hinge sets, and replacement parts for LiftMaster, FAAC, and Mighty Mule systems. If your part is in stock, which it usually is, we finish the job in one visit. If it’s a specialty Viking or DoorKing board that needs ordering, we’ll tell you before we schedule, so you know what to expect. Call (775) 210-7739 to find out whether your repair is same-day.

FAQs – Gate Parts & Welding Cost

How much does a gate hinge weld cost in Henderson?

A single gate hinge weld in Henderson runs $100 to $250. If the hinge itself is broken and needs replacement in addition to the weld, the total runs $150 to $350 per hinge. The price includes grinding the old weld, aligning the gate, and laying the new weld. Call (775) 210-7739 for a written quote on your specific hinge.

How much does it cost to weld a broken gate post?

Welding a broken gate post that’s otherwise structurally sound runs $200 to $500. If the post is too far gone and needs replacement with new concrete, expect $500 to $1,200. The variance depends on whether the post is in soil or block wall, and whether caliche makes the digging harder. Call (775) 210-7739 for a free estimate.

How much does electric gate repair cost in Henderson?

Electric gate repair in Henderson typically runs $150 to $900 depending on the component. A sensor or limit switch replacement is $150 to $400, a control board replacement is $250 to $600, and a full motor replacement is $400 to $900. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. Call (775) 210-7739 for an exact quote.

How much does a gate latch replacement cost?

A standard gate latch replacement in Henderson costs $120 to $280. A heavy-duty locking latch or a pool-compliant self-closing latch runs $180 to $450 depending on the hardware and whether it needs additional spring adjustment. The written quote covers the full installed price. Call (775) 210-7739 to get your latch price.

Do you charge for estimates on gate parts and welding?

No. The estimate is free. We come out, inspect the gate, and give you a written price before any work starts. If you decide not to proceed, you owe nothing. Call (775) 210-7739 to schedule a free estimate in Henderson.

What brands of electric gate openers do you repair?

We repair LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule gate openers. Parts for LiftMaster and Mighty Mule are usually in stock on the truck. Viking and DoorKing components sometimes need ordering, which extends the timeline by a few days, and we’ll tell you that before we schedule.

Why Henderson Homeowners Call Latch and Post Gate Repair

Every gate comes down to the latch that holds it and the post that carries it. That’s the work we focus on, and that focus means the technician at your door has seen a hundred hinges like yours, not three.

Our team is part of the Cedarwell family of independently owned and operated gate specialists. We’ve been doing this work since 2009, and the routine hasn’t changed: a live person answers every call at (775) 210-7739, day or night, weekends and holidays included. You don’t leave a voicemail and hope for a callback.

When the technician arrives, they’re background-checked, uniformed, and working under the Cedarwell C.A.R.E. values. Before we touch your gate, we put down drop cloths where we’re working and put on shoe covers if we step inside. We ask before we move anything. We explain the price before the work. And before we leave, we take a photo of the cleaned-up area so you can see exactly what we left behind.

If you have kids or pets, you can ask us to schedule around nap time. We use quiet tools where we can, and we choose pet-safe lubricants when there’s a choice. That’s not a special request; it’s how we operate.

And every repair, every weld, every latch replacement, every part we install carries the 365-Day Done Right Promise. If it’s not right, we make it right. That’s the whole promise, no fine print.

If your gate is sagging, won’t latch, or has a crack in the frame, don’t wait. The desert heat turns small cracks into broken hinges fast. Call (775) 210-7739 now for a free estimate, and you’ll have a written price before any work starts.

Written by Cody Beckman, Owner at Latch and Post Gate Repair Henderson, serving Henderson since 2009.

Pricing reflects the Henderson market as of 2026. Latch and Post Gate Repair Henderson offers free estimates – call (775) 210-7739.